Cabinet Connector Pinout
Every cabinet-side connector on the original I/O board, transcribed from the IKA Victor schematic recreation. These have not been fully re-verified by continuity; beep out any connector you intend to build a mating part for.
Conventions:
_SW— switch input, active-low, pulled up on the board._LIGHT— lamp output, sunk by aULN2803A. Lamp anodes go to the +12 V pin on the same connector.
P1 buttons — J7, Molex 5045-12A
| Pin | Signal | Pin | Signal |
|---|---|---|---|
| 1 | GND | 7 | P1_K3_LIGHT |
| 2 | P1_K1_SW | 8 | P1_K4_SW |
| 3 | P1_K1_LIGHT | 9 | P1_K4_LIGHT |
| 4 | P1_K2_SW | 10 | P1_K5_SW |
| 5 | P1_K2_LIGHT | 11 | P1_K5_LIGHT |
| 6 | P1_K3_SW | 12 | +12V |
P2 buttons — J10, Molex 5045-14A
| Pin | Signal | Pin | Signal |
|---|---|---|---|
| 1 | NC | 8 | P2_K3_LIGHT |
| 2 | GND | 9 | P2_K4_SW |
| 3 | P2_K1_SW | 10 | P2_K4_LIGHT |
| 4 | P2_K1_LIGHT | 11 | P2_K5_SW |
| 5 | P2_K2_SW | 12 | P2_K5_LIGHT |
| 6 | P2_K2_LIGHT | 13 | +12V |
| 7 | P2_K3_SW | 14 | NC |
Start and effector 1 — J4, Molex 5045-08A
| Pin | Signal | Pin | Signal |
|---|---|---|---|
| 1 | NC | 5 | P2_START_SW |
| 2 | GND | 6 | P2_START_LIGHT |
| 3 | P1_START_SW | 7 | EFF_K1_SW |
| 4 | P1_START_LIGHT | 8 | EFF_K1_LIGHT |
Effectors 2–4 — J3, Molex 5045-08A
| Pin | Signal | Pin | Signal |
|---|---|---|---|
| 1 | EFF_K2_SW | 5 | EFF_K4_SW |
| 2 | EFF_K2_LIGHT | 6 | EFF_K4_LIGHT |
| 3 | EFF_K3_SW | 7 | +12V |
| 4 | EFF_K3_LIGHT | 8 | NC |
P1 turntable — J6, Molex 5045-08A
| Pin | Signal | Pin | Signal |
|---|---|---|---|
| 1 | +12V | 5 | P1_TT_S1 |
| 2 | P1_TT_S0 | 6 | GND |
| 3 | GND | 7 | P1_TT_LIGHT |
| 4 | +5V | 8 | +5V |
P2 turntable — J9, Molex 5045-08A
| Pin | Signal | Pin | Signal |
|---|---|---|---|
| 1 | +12V | 5 | +5V |
| 2 | P2_TT_LIGHT | 6 | GND |
| 3 | GND | 7 | P2_TT_S0 |
| 4 | P2_TT_S1 | 8 | +5V |
Note the differing pin order between the two turntable connectors.
Test, service and counter — J2, Molex 5045-05A
| Pin | Signal |
|---|---|
| 1 | GND |
| 2 | SERVICE_WH_SW — white button |
| 3 | TEST_RD_SW — red button |
| 4 | COIN_CNTR — mechanical coin counter solenoid |
| 5 | +12V |
P1 pedal — J5, Molex 5045-02A
| Pin | Signal |
|---|---|
| 1 | P1_PDL_SW |
| 2 | GND |
P2 pedal — J8, Molex 5045-03A
Keyed, with two grounds.
| Pin | Signal |
|---|---|
| 1 | GND |
| 2 | GND |
| 3 | P2_PDL_SW |
Coin switch — J13, Molex 5045-02A
| Pin | Signal |
|---|---|
| 1 | COINSW |
| 2 | GND |
The 1N4148 isolation diode is on the board side of this connector.
Power — J12, Molex SPOX 5281-04A
TE 350211-1 is an equivalent part. Older guides describe this as a "5058" connector, which does not match the schematic.
| Pin | Signal | Note |
|---|---|---|
| 1 | +12V | Filtered by C1, 470 µF 25 V |
| 2 | GND | |
| 3 | GND | |
| 4 | +5V | Filtered by C2, 470 µF 16 V |
Neon and light controller — J11, 2×10 IDC
330 Ω series lines to the external AC relay board driving the neon tubes and
cabinet flashers. Bit-to-lamp assignment is per-cabinet; see the note on write
port 0x100 in bus-protocol.md.
Signal inventory
Totals for a direct replacement board.
Switch inputs — 21, all active-low with pull-ups: P1_K1–K5,
P2_K1–K5, P1_START, P2_START, EFF_K1–K4, P1_PDL, P2_PDL,
TEST_RD, SERVICE_WH, COINSW.
Quadrature pairs — 2: P1_TT_S0/S1, P2_TT_S0/S1.
Lamp outputs — approximately 25, all ULN2803A sinks: P1_K1–K5,
P2_K1–K5, P1_START, P2_START, EFF_K1–K4, P1_TT_LIGHT,
P2_TT_LIGHT, COIN_CNTR, plus the neon channels.
Supplies at the connectors — +5 V for the encoders, +12 V for the lamps, and ground.
This page is synced from docs/connector-pinout.md in the ez2-io repo.